Magnet Coating Selection Guide | King-Nd Magnet

Standard Industrial Coatings

Most sintered NdFeB magnets in general industrial use are protected with one of four low-cost coatings, covered under GB/T 34491 "Surface Coatings for Sintered NdFeB Magnets".

CoatingTypical strengthsTypical trade-off
Nickel-Copper-Nickel (Ni-Cu-Ni)High mechanical strength, good general corrosion resistance, tolerates heat and thermal cycling well, bright finishNot the best choice for strong chemical or salt-spray exposure; nickel can trigger skin allergy on direct, prolonged skin contact
Blue-White ZincLow cost, adequate protection for dry indoor useWeaker moisture/chemical resistance than epoxy or Ni-Cu-Ni
Black EpoxyStrong moisture, chemical and salt-spray resistance; electrical insulationOrganic coating — outgasses under heat/vacuum (see Aerospace section below); matte black finish only
ParyleneUltra-thin, pinhole-free, strong chemical resistance, biocompatible, low cytotoxicityHigher cost than Ni-Cu-Ni or zinc; requires CVD equipment/process control

When to Consider a Precious-Metal or Specialty Coating

Standard plating is not chemically inert enough for a handful of demanding applications. In these cases, gold (Au), platinum (Pt), silver (Ag), rhodium (Rh) or an engineered coating such as titanium nitride (TiN) are used instead — each for a specific, verifiable technical reason, not simply as an upgrade.

1. Implantable & Direct Biomedical Contact

Cochlear implant magnets, implantable pump/valve components, magnetic muscle trackers for limb prostheses, magnetic dental attachments
Titanium encapsulation (dominant practice) · Parylene C, gold or TiN direct coating (research/niche use)

Nickel and copper ions released by ordinary plating are cytotoxic and can trigger inflammation or rejection inside the body, so an implanted magnet cannot use standard Ni-Cu-Ni or zinc coating.

Correction to a common assumption: for magnets that are actually implanted in tissue (e.g. cochlear implants), the dominant real-world practice is not direct gold or platinum plating — it is hermetically sealing the whole magnet inside a welded titanium (or titanium-alloy) housing, so the magnet material never contacts tissue at all. Direct coatings are studied as an alternative for cases where a housing isn't practical: a peer-reviewed 2021 study (Vidal et al., RSC Advances) compared gold, titanium nitride and Parylene C as direct coatings on implanted NdFeB magnets and found Parylene C performed best for corrosion prevention and cytotoxicity in muscle-tissue testing — gold was not the clear winner. Treat "gold for implants" as one option among several being researched, not a default.

2. Strong Chemical / Marine Corrosion

Magnetic stirrers and flowmeters in strong-acid/alkali chemical processing, chromatography instrument components, seawater-exposed sensors
Gold · Platinum · Rhodium

Standard Ni-Cu-Ni plating can develop micro-pitting corrosion under strong acid, alkali or high-salinity (e.g. seawater) exposure. Gold, platinum and rhodium are chemically inert enough to resist this, at a materially higher coating cost.

3. High-Frequency / Low-Contact-Resistance Electronics

Precision micro-connectors, high-frequency relays, precision electronic switches, RF/microwave magnetic components
Gold · Silver

Silver has the highest electrical conductivity of any metal; gold has very low contact resistance and does not form an insulating oxide layer on its surface. When a magnet also serves as an electrical contact or signal path — not just a magnetic source — these properties keep contact resistance low and stable over time. Silver also has natural antibacterial properties, which is sometimes a secondary reason for choosing it in medical-adjacent electronics.

4. Aerospace & Ultra-High Vacuum (UHV)

Satellite attitude-control systems, space-station precision instruments, UHV physics equipment
Gold

Organic coatings such as epoxy outgas under heat and vacuum, which can contaminate a vacuum chamber or fog nearby optics — this is exactly what the aerospace industry's ASTM E595 outgassing standard (developed by NASA) screens for, with pass criteria of ≤1.0% total mass loss and ≤0.1% collected volatile condensable material. A dense, non-outgassing gold layer avoids this failure mode and also offers some resistance to radiation and atomic-oxygen erosion in low Earth orbit.

5. Jewelry, Premium Consumer Goods & Skin-Contact Decorative Parts

Magnetic jewelry clasps, premium headphone/smartwatch components, leather-goods magnetic closures
Gold · Rhodium

Nickel allergy is common enough that sustained skin contact with a nickel-containing coating is a real concern for consumer products. Gold or rhodium plating gives a premium gold or bright-white finish while fully isolating the skin from the nickel layer underneath.

Other Coatings Worth Knowing About

The five scenarios above aren't the only specialty options. Depending on the application, these are also worth discussing with our engineers:

Coating / approachWhere it's usedWhy
Titanium (or stainless steel) hermetic encapsulationImplantable medical devices, harsh-environment sensorsIsolates the magnet completely rather than relying on a thin coating — the standard approach for direct tissue contact (see Scenario 1)
Titanium Nitride (TiN), PVD-appliedOrthopedic/dental implant components, wear-resistant precision partsHard, biocompatible ceramic-like coating; studied as a candidate direct coating for implanted NdFeB magnets alongside gold and Parylene C
PTFE (Teflon)Implantable hearing-device magnets, low-friction mechanical partsChemically inert, non-permeable polymer barrier — an alternative to Parylene in some implant designs
Passivated / phosphate coatingsLow-cost general corrosion resistance on non-NdFeB ferrous partsCheaper pretreatment layer, sometimes used under paint or as a standalone light-duty finish

How to Use This Guide

A short decision process, in order:

  • Start with the standard coatings table. If your magnet is used indoors, outdoors, or in a chemically mild environment, one of the four standard coatings almost always covers it at the lowest cost.
  • Check if your application matches one of the five specialty scenarios. If it involves direct or implanted contact with the human body, strong acid/alkali/seawater exposure, a role as an electrical contact, vacuum/aerospace service, or sustained skin contact on a consumer product, move to the precious-metal or engineered-coating options.
  • For implantable or in-body contact specifically, talk to our engineers about hermetic titanium encapsulation before defaulting to a direct coating — it is the more established, lower-risk approach for most implant designs, and carries different regulatory documentation than a plated coating.
  • Confirm certification requirements separately from coating choice. A biocompatible coating (Parylene, gold, TiN) does not by itself satisfy medical-device regulatory requirements (e.g. ISO 10993) — certification testing is still required on the finished part.

References

  • GB/T 34491 "Surface Coatings for Sintered NdFeB Magnets" — coating types and classification for this material
  • ASTM E595 "Standard Test Method for Total Mass Loss and Collected Volatile Condensable Materials from Outgassing in a Vacuum Environment" — the NASA-developed outgassing standard referenced in the Aerospace scenario
  • Vidal, C. V. et al., "Assessment of biocompatible coating materials for implantable NdFeB magnets," RSC Advances, 2021, 11, 5081 — the gold vs. TiN vs. Parylene C comparison referenced in the Implantable scenario

Engineering Reference

This guide describes general coating characteristics and common industry practice, not a certification or a quantitative spec (salt-spray hours, coating thickness, outgassing test result) for your specific part. Medical, aerospace and other regulated applications require their own certification testing regardless of which coating or approach you start from — please work with our engineers on the exact requirements for your project.

Not sure which coating fits your application?

Share your operating environment, contact requirements and any regulatory standards you need to meet, and our engineers will recommend the right coating or encapsulation approach.

Talk to a Specialist →
Want a free sample? Under 1 minuteTell us your shape, grade and coating, then add your email. Takes about a minute.
Get My Free Sample →
Scroll to Top